We have found the article on Tools You Need to Install a New Bathtub down the page on the internet and decided it made sense to share it with you here.
Installing a bathtub isn't exactly rocket science, yet it does need strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough job. If the old bathtub is conveniently obtainable, the job can move immediately; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually currently purchased a new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
- New Bath tub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Tape Measure
- Pipe Caps
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the water supply as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also examine the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bath tub has been made use of at least when as this will settle it right into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that report about Tools You Need to Install a New Bathtub from a good friend on our other website. Are you aware of somebody else who is fascinated with the topic? Please feel free to share it. Thank you so much for going through it.
Automated Marketing
Comments on “Do It Yourself Bathtub Installation.”